Rosin core tin-lead solder wire BBIEN TL-01 Sn63Pb37
Brief Description for TL-01 Sn63Pb37 solder wire
BBIEN TL-01 Sn63/Pb37 leaded no clean pb solder wire is a flux-cored solder wire. Solid type also available. This cored solder version Sn-Pb alloy wire is more effective than rosin fluxes in soldering difficult metals. The same fast action and mild properties are exhibited with rosin based flux soldering. The flux is more heat stable than most organic fluxes, resulting in minimal smoke and odor. The residue no need to clean.
BBIEN TL-01 Sn63-Pb37 flux core solder wire is the most common type and best quality of tin-lead alloy solder, which features the maximum dosage and demand. 63/37 tin lead welding wire represents that the alloy contain 63% tin content and 37% lead content in the solder, the diameter of Sn63Pb37 solder wire is from 0.35mm to 6.0mm. It is mid temperature solder wire which its melting point is 183degree Celsius. Sn63Pb37 no clean flux core solder wire can offer quite stable welding performance.
Datasheet of BBIEN TL-01 Sn63Pb37 core wire solder
Impurity content %
Sn63Pb37 solder wire physical properties arability balance
Heat cubage（J/kg · k）
Brinell Hardness/ Rigidity (HB)
Conduct heat（J/m · s · K）
Tensile Strength/Extend intension（MPa）
So far,our Sn63Pb37 core solder wire have been exported to Bangladesh,Pakistan,Saudi-Arab, Colombia, Russia,India, Pakistan, Romania etc.
BBIEN TL-01 Sn63Pb37 leaded solder wire can be used in the electronics,copper plate, semiconductor ,Hard disk drive,Optics-electronic, LCD, IC, SMT, PCB ,Medical field and biotech industries.
core solder wire/solid wire
Bright alloy appearance
100g,200g,250g,500g 500g,1kg per reel/bobbion；10kg/carton: 30kg/carton
Size of 30kg carton:36x18x20cm
Solder iron tip temperatures are most commonly between 150-210°C for Sn63Pb37 and Sn62Pb36Ag02 alloys, and 210-350°C for lead-free alloys. Heat both the land area and component lead to be soldered with the iron or air gun prior to touching the land with the cored wire. Do not apply the wire directly to the soldering iron tip. If needed,BBIEN TL-01 Sn63/Pb37 solder wire organic flux may be used as a compatible liquid flux to aid in reworking soldered joints..
BBIEN TL-01 Sn63-Pb37 flux residue is conductive and will cause corrosion of metal parts over time. Residue removal should be completed within 48 hours. LF-01 flux has the advantage over many competitive not water-soluble flux formulations,but it is belong to no-clean type.
HINTS And TIPS ON SOLDERING IN GENERAL
Always remember that a soldered joint is formed by heating the parts to be soldered to a temperature in excess of the melting point of the alloy to be used – in hand soldering this is how a soldering iron is used. By feeding the cored wire onto the parts, the flux is able to flow and remove oxide films, while the solder creates a thin inter-metallic bond which becomes the solder joint.
Note the following tips:
• Cored solder wires can be provided in different grades of alloy so always ensures that you have selected the right grade for the application.
• Do not overheat as this causes an increase in the depth of the inter-metallic layer, which in turn weakens the joint. All materials from Alpha Metals are manufactured to meet the most stringent of standards and to ensure the best possible finish to every soldering application.
• Use a soldering iron bit size and form to suit the operation: small bits for soldering large components may prevent the formation of a joint or slow the process down.
• Always select wire diameters to suit both soldering iron bit and the parts/components to be soldered.
• Soldering iron systems should provide sufficient heat to satisfy the requirements of the points above.
Storage and Shelf Life
The shelf life of cored solder wire is based on the chemistry of the flux core and the protective alloy covering of the wire.
When stored in a dry, non-corrosive environment between 10°C-40°C (50-104°F), the shelf life of wire may be nearlyindefinite. The expiration date determined by the date of manufacture printed on the product and Certificate of Analysis will represent the manufacturer’s warranty period which is the time frame wherein BBIEN will replace defective product.
Flux-cored solder wires with alloys containing more than 70% lead have a 2 year warranty from the date of manufacture.
All other alloys have a 2 year warranty from the date of manufacture.
Over time, the surface of wire may lose its shine and appear a dull shade of gray. This is a surface phenomenon and is not detrimental to product functionality.
Other type of lead based solder wire:
Computers, precision instruments, meters, TV,
micro technology, coating metals
Calculators, tape recorders, telephones, quartz and
other common electronic and electrical products
General circuit boards, toys, lamps, crafts, water tanks, plumbing solder
General circuit boards, toys, lamps, crafts, water tanks, plumbing solder
How to chose solder
Select the solder composition. First choose between leaded or lead free and then between high or low temperature. Choose high temperature for easily accessible connections and low temperature for smaller, crowded connections. Next choose the alloy. Leaded solder ranges from 40 percent tin and 60 percent lead (40/60) to 50/50, 60/40 and 63/37. The first number always represents the tin content; the higher the tin content, the lower the melting point. The most common lead-free solder contains 95 percent tin and 5 percent antimony but has a melting point between that of 40/60 and 50/50 tin/lead solder. Only experience will direct you in making exact choices for your application
Select the diameter of the solder wire, from between 0.01 inch (0.25 mm) to 0.125 inch (3.25 mm). You must heat the metals to melt the solder as quickly as possible. The smaller the diameter of the solder wire, the faster it will melt. But if you choose too small of a diameter, you will not get enough solder on the joint in one pass. If you choose too large, excess heat may damage your components, or you may get a solder blob.
Select flux core or no core. All solder joints need flux, which can be applied from a tube, with a brush, from the core of the solder or in any combination, depending on your personal style. But you must apply flux in one manner or another. The style you develop for soldering will determine the best choice for your application, but to be safe, always use a flux core so that you don’t forget.
Photos of BBIEN TL-01 Sn63Pb37 solder wire
Rosin core tin-lead solder wire Sn63Pb37
■Excellent solderability to a wide variety of metalizations
■Easy removal in hot DI water
■Compatible with leaded and lead-free alloys
■Classified as ORH1 per J-STD-004
Favorable fatigue resistance and outstanding performance
Ultra high electrical conductivity
Mid-temperature soldering,characterized by nice softness and wonderful wetting property.
High-performance soldering flux,fast melting speed,good fluidity and quick speed to coat with tin.lower soldering flux spatter rate during soldering.
Sldering flux is evenly distribution with good continuity and very little smoke and smell gas
In addition,Sn63Pb37 also have the following charateristics
1. Can applied in radio,communication,meters and instruments
2. Residue is easy to remove by hot air after soldering work if necessary
3. Available in many alloy compositions
4. Smooth surface,good fluid melting rate
5. Good mechanical performance,moisture and bright weld spot
6. Forms:bar and wire
7. Flux types:no-clean,rosin and water-soluble liquid
8. Tin solder,welding,lead-free solder bar and wires are also available
9. Very few scraps.
Advantage And Service
Rosin core tin-lead solder wire Sn63Pb37
BBIEN is specialized in soldering industry from 2000,known as a experienced tin lead and lead free solder wire manufacturer,whose products are made in China,since then,BBIEN pays high attention to Research and Development,continuous technical innovation for pb and pb free solder wire industry,until now,we accumulate much valuable experience,five senior solder wire engineers operate a specialized reflowing solder wire production.
BBIEN TL-01 Sn63Pb37 middle temperature 183 degree Celsius Pb contained tin based soldering wire can be packaged with spool,general 200g,250g,500g,1000g spool,which is used for both hands soldering and air soldering technique.
Due to sophisticated technical in Sn-Pb alloy,BBIEN can supply the thinnest diameter size to 0.3mm for BBIEN TL-01 Sn63Pb37 no clean solder wire,normal size such as 0.3mm,0.5mm,0.6mm,0.8mm,1.0mm,1.0mm,1.5mm,2.0mm solder wires are all available.
Best quality no clean solder wire BBIEN TL-01 Sn63Pb37 is 183 degree melting point lead solder wire offers excellent solderbility,wettibility and reliability among leaded Pb contained solder wire,it is available in a wide product lineup according to the required soldering temperature.
Thanks to BBIEN long-term unremitting R&D for solder technique,until now,BBIEN have the following high-tech solder product for different lead free alloy.
BBIEN TL-01 Sn63Pb37 tin-lead no clean rosin leaded solder wire can be not only applied to tradional electronics pcb,electronics soldering,but also its application for some new hi-tech industry, semiconductor. LED, aerospace, automotive.
Very good constant flow and wetting,clear and transparent residues
200g/roll：96spools/export carton:G.W-19.2kg;Size of Carton:36*26*18cm
250g/roll：96spools/export carton:G.W-12kg Size of Carton:36*26*18cm
500g/roll:40rolls/export carton:G.W-20kg Size of Carton:36*26*18cm
1kgg/roll:51/rolls export carton：G.W-40kg Size of Carton:36*26*18cm
OEM can be discussed,we will use our own label if customers have no other requirement.
No clean lead-free solder
Solder wire alloy
Solder bar/block alloy
Solder paste alloy
Solder powder alloy
low cost,the most commonly used;
high cost,relatively bright spot;
BBIEN can share the datasheet for our product to our clients.
Certificates of compliance,SGS,ISO and COA,MSDS,are available.
We are tyring to make our product quality system more and more complete,BBIEN also appreciate your precious suggestion.
Both pre-sale and after-sale,BBIEN have skilled person to follow-up our client,reply answer for reasonable price,relevant quality standard,products data informations,shipping for your questions skillfully ,quickly, technical support is available.
Mutiple-transportation oversea shipping ways by ari,by sea,by train and truck road way ensuring the shipment can arrive at destination all around the world safety,quickly and efficiently.
Shipment can be deliveried once placing order 2 to 10 working days.
Shipment will be regular go through local custom and its warehouse,BBIEN has own specialized shipping team and operators agent all over the world.
When you send us message,BBIEN will feedback you general within 2 working hours.Our customer service or sales person will be match with you above 10-24hours.And solve your problem on solder products.
OEM is available according to your own logo.
1.Do I need to pay the charge for sample?
We offer the small free sample for testing,but the courier charge should be paid by your side.
2.How about your product quality,guaranteed?
Our products through strict quality control and inspection before leave factory,and has passed the SGS.
3.What is your delivery time?
2-3days for delivery sample
2-3days for standard goods in stock
5-7days for normal order
7-12days for customize order
4.Any other special metal items that you make too?
We produce Zn wire,Sn wire,Mo wire,Indium wire;
We still make special metal alloy:e.g.,Sn-Bi,Ag-Al,Sn-Sb,Sn-Ag,
Ge metal;In metal etc
A variety and flexible of payment terms,T/T,western union,paypal,L/C can be acceptable.
Prodution ability:6tons each day for normally solder wire diameter above 1.0mm,packing 1kg/spool
Delivery time:within 7working days after confirming payment infos.
Why choose us?
*We are the manufacturer of solder items,special metal alloy, you can buy the suitable products you need at reasonable prices.
*Our customer service personnel will provide you with our competitive quotation as well as expedite your orders&provide you with any assistance you may require.
*Sales engineers are available to offer help recommending the most suitable products for your application and solve problems once you find problem to use our products.
*We can accept OEM or ODM,use your brand name and logo on the solder reel!
*Promptly delivery and small sample order is available.
Return back to society
BBIEN also participates public benefit activities,return back to society.We support and want to create a environmental friendly society together with people.We also try our best to help someone who need us.
Application Photos for BBIEN-TL-01 Sn63Pb37 solder wire
BBIEN Technology is one of the professional manufacturers and suppliers of rosin core tin-lead solder wire sn63pb37. We have professional workers who have consummate skills producing high quality products in our factory. Welcome to buy our discount and low price rosin core tin-lead solder wire sn63pb37 made in China. Pricelist and quotation consultation are available if you need.